Halaman utama Jelajahi Bantuan
Daftar Masuk
XCAppCollection
/
XCVMKit-OS
2
0
Fork 0
Berkas Masalah 0 Permintaan Tarik 0 Wiki
Cabang: master
Ranting Tag
XCVMKit-OS
/
package
/
wilc-driver
/
Config.in

Config.in 2.3 KB
Permalink Riwayat Mentahan

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364 
  1. config BR2_PACKAGE_WILC_DRIVER
    2. 

  2. 	bool "wilc kernel module"
    3. 

  3. 	depends on !BR2_s390x
    4. 

  4. 	depends on BR2_LINUX_KERNEL
    5. 

  5. 	help
    6. 

  6. 	  External kernel module for WILC1000/3000 devices.
    7. 

  7. 

  8. 	  wilc kernel driver source as found in Microchip's at91-linux
    9. 

  9. 	  kernel tree with added Kbuild file to be built as a generic
    10. 

  10. 	  external module.
    11. 

  11. 

  12. 	  The wilc1000 driver currently maintained in Linux kernel does
    13. 

  13. 	  not support BLE of the WILC3000 hardware. This package is
    14. 

  14. 	  meant to bridge that gap until Microchip can get WILC3000
    15. 

  15. 	  support upstream.
    16. 

  16. 

  17. 	  Supports both SDIO and SPI modes.
    18. 

  18. 

  19. 	  https://github.com/embeddedTS/wilc3000-external-module
    20. 

  20. 

  21. if BR2_PACKAGE_WILC_DRIVER
    22. 

  22. 

  23. config BR2_PACKAGE_WILC_DRIVER_SPI
    24. 

  24. 	bool "SPI"
    25. 

  25. 	help
    26. 

  26. 	  This module adds support for the SPI interface of adapters
    27. 

  27. 	  using WILC1000/3000 chipset. The WILC1000/3000 has a Serial
    28. 

  28. 	  Peripheral Interface (SPI) that operates as an SPI slave.
    29. 

  29. 	  This SPI interface can be used for control and for serial
    30. 

  30. 	  I/O of 802.11 data. The SPI is a full-duplex slave
    31. 

  31. 	  synchronous serial interface that is available immediately
    32. 

  32. 	  following reset when pin 9 (SDIO_SPI_CFG) is tied to VDDIO.
    33. 

  33. 	  Select this if your platform is using the SPI bus.
    34. 

  34. 

  35. config BR2_PACKAGE_WILC_DRIVER_SDIO
    36. 

  36. 	bool "SDIO"
    37. 

  37. 	help
    38. 

  38. 	  This module adds support for the SDIO interface of adapters
    39. 

  39. 	  using WILC1000/3000 chipset. The WILC1000/3000 SDIO is a full
    40. 

  40. 	  speed interface. It meets SDIO card specification version 2.0.
    41. 

  41. 	  The interface supports the 1-bit/4-bit SD transfer mode at the
    42. 

  42. 	  clock range of 0-50 MHz. The host can use this interface to
    43. 

  43. 	  read and write from any register within the chip as well as
    44. 

  44. 	  configure the WILC1000/3000 for data DMA. To use this
    45. 

  45. 	  interface, pin9 (SDIO_SPI_CFG) must be grounded. Select this
    46. 

  46. 	  if your platform is using the SDIO bus.
    47. 

  47. 

  48. if BR2_PACKAGE_WILC_DRIVER_SDIO
    49. 

  49. 

  50. config BR2_PACKAGE_WILC_DRIVER_SDIO_OOB
    51. 

  51. 	bool "Enable out-of-band interrupt"
    52. 

  52. 	help
    53. 

  53. 	  This option enables out-of-band interrupt support for the
    54. 

  54. 	  WILC1000/3000 chipset. This OOB interrupt is intended to
    55. 

  55. 	  provide a faster interrupt mechanism for SDIO host controllers
    56. 

  56. 	  that don't support SDIO interrupt. Select this option If the
    57. 

  57. 	  SDIO host controller in your platform doesn't support SDIO
    58. 

  58. 	  time division interrupt.
    59. 

  59. endif
    60. 

  60. endif
    61. 

  61. 

  62. comment "wilc kernel module needs a Linux kernel to be built"
    63. 

  63. 	depends on !BR2_s390x
    64. 

  64. 	depends on !BR2_LINUX_KERNEL
    65.